Thoughts on Apple's new products in 2018 and 2019

Apple had a grand event in October 2018, and these are my take-aways:

Lightning is going away.

The newest iPads no longer have a Lightning connector. Instead, the new iPads sport a standards-based USB-C connector. Additionally, the new Apple Pencil no longer has a Lightning connector.

I suspect that no new Apple devices will have a lightning connector.

Goodbye, Lightning. You were great in 2014, but USB-C made you redundant.

Mac Growth has Stopped ... by design.

Mac sales are more profitable than ever, but Apple has significantly slowed down the release of new Macs. At one time models were updated every 8 months on average, but now Mac models are sold for several years without updates. Furthermore, Apple has stopped selling machines built and priced for secondary school students.

Although Apple continues to be within the top five PC manufacturers, Mac sales are declining compared to the competition. And with fewer sales, fewer developers will be investing in Mac software production.

Engineering investment should be focused on Apple's most promising product lines, and that's not the Mac. At this point, Apple's strategy is to maximize Mac profits at the cost of its ecosystem. Because the Mac ecosystem has no future.

Goodbye, Mac. You were great in 2010, but iOS has made you a poor investment.

Canon SD890 Review

My Canon PowerShot SD890IS Review Wahoo! I just received my new Canon PowerShot SD890IS . Here's my review of the new SD890IS. Updated! (20-April-2008)! I like taking good photos. And I hate lugging around big cameras and equipment. And so I concluded that I needed to buy myself an awesome point-n-shoot camera. I often take pictures in difficult conditions, such as a museum where a flash camera is prohibited. Or a concert, where I can't use a flash, the lighting is low, and the people on stage are in motion. Or with the zoom cranked up and focused on a distant subject. Taking good photos in these conditions, with a small lens camera and without a tripod is a challenge at best. In comes the SD890. I was particularly excited about the SD890 because it is pocketable, yet it has awesome specifications: Image stabilization ; a 5x zoom lens, and 10 megapixel resolution. When I bought the camera, I imagined that these features would help me take much better pictures in the...

The Trick to Properly Fixing the Rubber Feet of a MacBook Pro

A black rubber foot of my trusty old MacBook Pro finally broke off, and I didn't like how it made the laptop wobbly. A fix was needed, and quick! First I bought some replacement feet, the kind that just stick on. These feet are nice because there is no need open up the machine to fix a broken foot. They're very inexpensive, and the ones I bought have adhesive tape already applied - just peal and stick. I bought feet like the ones found here. I have read many complaints about how the adhesive doesn't stick, but I think that's because people don't know the two tricks required to get the new feet to stick properly. New Feet to replace a lost Foot Important Trick 1: Make sure to remove all remnants of the old foot - including the pieces in the hole. My factory-installed foot was attached both mechanically and with adhesive, but when the old foot sheared off, some pieces of the old foot remained in the hole. Those plastic bits would h...

Fix a Lightning Cable with Heat Shrink Tubing

We've all seen a Lightning cable that has started to fall apart. They get used every day, and after enough tugs and yanks on your iPhone, they start to fray. I've seen a lot of these frayed cables, so I've started to fix them before they break with heat shrink tube. I get my heat shrink on Amazon, like this handy and inexpensive pack. I prefer the heat shrink tubes without internal glue - it has higher flexibility and a smaller outside diameter once shrunk. Heat Shrink Tubing on an Old, Frayed Lightning Cable In the photo here, you'll see that I slid on a 1.25 inch length of heat shrink over the lighting connector, and then shrunk it into place. I chose a diameter that just barely fits over the lightning connector. In all, it took about 60 seconds to perform this repair. Warning: the white plastic of the lightning cable has a pretty low melting point. It seems to start to melt at about 125°C (or about 250°F), which is the same temperatur...

Repairing a MagSafe Charger's Cord

Here is how to repair the cord of Apple MacSafe power adapters. There are three common failure modes of a magsafe wire: The base of the cord becomes frayed where the wire enters the power brick. This is usually caused by repeatedly wrapping the cord far too tightly around the brick's "ears". The head of the magsafe connector becomes frayed. This is usually caused by repeatedly removing the magsafe magnet by yanking on the cord. Chewed up cord. This is where a pet or other pinching device weakens the cord. These types of failure are usually repairable at home using the technique described here. Tools Required: A beginner's Soldering kit, like this one, including a low-wattage soldering iron, rosin-core Solder, and wire strippers. Heat shrink tubing . Any color works, but these days I use white to repair a MagSafe cord. One Soldering Sleeve, appropriate for 22 or 24 AWG wire Heat gun (optional.) Process: The general process is t...

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair. Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator. Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way. Note in the pictures how I approach these tabs with my screwdriver. I usually release the left side first, and then I release ...

Hot (and Cold) Attic Tempertures and Electronic Equipment

An unfinished attic can be an extreme environment for electronic equipment, with conditions that are very unlike what is experienced inside normal living spaces. What's the deal with installing electronic equipment in an unfinished and uninsulated attic? I wanted to install a standard WiFi router in my attic to function as a Wireless ISP (WISP) gateway. My attic is a fantastic location from a radio signal perspective, but it is an uncomfortable place for both people and electronic gear. Although the attic is well insulated, that insulation is on the floor, designed to keep the living space of my home at moderate temperatures. As a WISP gateway, my WiFi router is best mounted above the insulation and close to the roof, where the only protection from weather extremes is the wood of the roof and a layer of asphalt shingles. Equipment Specifications and Extremes Almost all electronic equipment has a set of specifications regarding operating environment. These specifications state the...

The Lance J. Technoweb

Search This Blog