Fujitsu S-Series Repair

Fujitsu S-Series Lifebook Laptop S6110The Patient: Fujitsu S-Series Laptop

The power connector of my S-Series Fujitsu laptop failed (a Lifebook S6110), just like so many others out there. I called up Fujitsu for repair; their local service center wanted about $80 just to look at the laptop (which obviously only needed a new connector). I concluded that it was silly for me to throw $80 at an estimate for repairing the power connector, so instead I went after repairing it myself.

Researching the problem.

At first I looked on the web for the right connector. After searching high and low, I found that the Asia Industrial Company appears to sell a very similar part, the DS-208. Let me know if you contact them for this jack.

I also saw a part for sale by a laptop power jack "repair" web site, but it didn't look like it would be mountable on my laptop's motherboard - the pins are in a different location, and I think it'd be very difficult to properly mount this part inside of my laptop.

Going at it.

Some ugly pigtailsPigtails off of the board

I decided to start by adding a few pigtails to the motherboard. I opened the laptop, with the helpful instructions found here. Then I soldered in a short length of wire.
From there, I added a simple connector on the end of the pigtail.

Fujitsu Laptop Repair: Power connector repairedPhase 1 complete, Lifebook operational!

At least my laptop is now, um, laptop-able once again. It does look a bit silly with the pigtail, but is is fully functional. I hope to acquire the correct DC Jack for the laptop. Please contact me if you have any leads or advice.

Beyond the Fujitsu

My next step will to try to get that DS-208 part and give it a shot.

To be honest, my Fujitsu is getting a little old, so I might end up buying another new laptop. There are a lot good laptops out there... and that's why I didn't initially go for the "Fujitsu service center" repair.


Thanksgiving Centerpiece (or, fun with paper mache)

Every year, one person in my family is assigned to make a special thanksgiving day centerpiece for the dinner table. This year I was assigned to make something.

Fulfilling my obligation, I have created a paper mache Turkey, the center of the American thanksgiving celebration. Read on to see how to make this Thanksgiving Centerpiece Turkey, the official Pilgrim Turkey of Thanksgiving.

Gobble Gobble! You can make me too!

Strangely, most people don't know the story of how Thanksgiving became synonymous with turkey. But first, maybe you'll want to know to build this handsome fellow...

Building the Turkey

I started with a couple small balloons, some coat hanger wire, and masking tape. I formed the body and head with the balloons and taped them together. I bent the coat hanger wire to form the beak and legs/feet. Some needle nose pliers helped me bend the wire.

Balloons, tape and wire. Note that I taped the feet to my work surface.

The beak frame. I drew a face on the "head" baloon so I could position the beak, then I taped the beak wire frame in place.

From there, I used standard papier mache techniques to coat my beast. I made a simple flour-and water paste (boil 1/4 cup flour in one quart of water for 5 minutes; let cool) and thinly coated newspaper strips with the stuff. Then I carefully coated the bird. It took a long time to coat him - several sessions over several days. I later added some plumage in the rear using inflated latex gloves :-). I also added some stubby wings, made out of cardboard from a Trader Joe's Pizza box and (of course) more masking tape.

With a coat of paper mache, the bird starts to take shape

I built a small hat out of a tube of cardboard and masking tape. I coated the tube with more paper mache in order to provide uniformity and to hide tape and gaps.

The Hat: papier mache coated cardboard

I took the whole project outside and sprayed it with a couple coats of brown spray paint. Being all brown, he looked like a giant chocolate turkey! Whoops! After the spray, I took him inside and gave it a final coat of brown with some brush-on paint, giving him a little more tecture than what the spray paint could provide.

Next, I painted the hat, and the details like the eyes (white paint with sharpie-black pupils).

Finally, I used a small, red deflated balloon to create his attractive wattle (a.k.a. "gobbler" or "flabby thing on his head")

The Pilgrim Turkey Project: Complete!

The Myth of the American Turkey

In the year 1584, Captain John Smith, a military officer and patriot, came to America in order to support the colonists with their admittedly poor farming skills. Times in America were tough - there wasn't much food, and many families were starving. But Smith was an avid amateur farmer, and before long he grew thousands of bushels of potatoes, cranberry, apples and corn for all of the people.

One of John Smith's duties was that of providing entertainment. He wasn't a particularly good at entertainment, and he decided that he'd have a big dinner party for "everee God-feering man and wo-man in thee towne". While walking to the feast, with his potatoes, cranberries and corn, Smith saw and captured a giant wild turkey, "so giantik and bulbous a beast that he shalt feed hundredsuch plainfolk".

Smith brought the huge turkey to the thanksgiving celebration where he met Pocahontas, the beautiful and petite Native American princess and avid gambler. On a wager with Smith, Pocahontas attempted to ride on the back of the giant bird, and found, in fact, that she could. Being a princess, she immediately exercised her pardoning privilege and pardoned the turkey from eating. She promptly left for home on the back of the turkey.

Pocahontas became the first domesticated turkey farmer in America - and in fact, every domestic American turkey is a decendant of the turkey that Pocahontas saved. Pocahontas later travelled to England to sell turkey meat, but that's another story.

Every thanksgiving, the President of the United States cerimonially pardons the thanksgiving turkey in memory of Pocahontas, John Smith, and their giant pilgrim turkey.


CFL Update - Save Electricity, Save Money.

I've been receiving a lot of questions and comments on compact fluorescent light bulbs ("CFLs"). Why? Well, maybe because electricity rates are almost three times as much as they were only a few years ago!

I have replaced most of my traditional "incandescent" light bulbs with CFLs. Replacing old-fashioned bulbs with "fancy" CFL bulbs has reduced my electric bill by more than half - or hundreds of dollars per year - at very low cost.

Light bulbs
I find that a GE 27 Watt CFL (on left) is substantially brighter than the 100 watt traditional bulb (right)

CFLs are more expensive than regular light bulbs, but they use much much less electricity and last much longer. I've paid between $0.99 and $3.50 per CFL bulb, depending on the type and style.

Bulb Recommendations

I have used CFLs from various manufacturers. I have been happy with modern bulbs from LightWiz, GE, and Phillips. I purchased some bulbs from Ikea a couple years ago, and they work well too. However, I imagine that Ikea buys their bulbs from various manufacturers, and so your mileage may vary.

Some readers say that they have had premature CFL bulb failure when mounted in some enclosed ceiling light fixtures. I have never had a CFL fail, and I have several enclosed light fixtures. In any case, note that some bulbs may be labeled as "inappropriate for enclosed fixture use". I recommend that you heed the manufacturer's label.
Enclosed fixture
Readers report that some CFLs can fail prematurely in an enclosed light fixture like mine. After 3+ years, I haven't had a problem.

Dimmers and Timers

Most CFLs are incompatible with dimmers. If you plan to use a CFL in a dimming circuit, make sure you get a CFL that is designed and sold for use with dimmers. In my experience, a CFL on a dimming circuit wildly flickers, or doesn't work at all. I don't have any dimmers, and therefore I cannot comment on the quality of dimmable CFLs.

Many low-quality, over-priced wall timers don't work with CFLs due to their cheap design. The answer? Buy a Swylite LST100 wall timer - it looks great and is much more functional than the ones I've bought at the local home store. Oh, and they cost less too.

Swylite LST100 timer I bought new on eBay

Warm-Up Issues

Other readers have complained about CFL "warm up time" when a CFL takes several seconds or even minutes to get to full brightness, especially in cold temperatures. This seems to be an issue with some old-style CFLs and some lousy brands. I did have a problem with some cheapo off-brand bulbs I bought at the Home Depot in 2004. These lousy CFLs were always very slow to get to full brightness, so I put them in the basement fixtures where I don't mind the slow start time. I recommend that you stick with modern name-brand bulbs. Ask your local lighting store to show you the startup characteristics of the bulbs you're buying.


Saving Electricity and Reducing Costs

Since everyone from the President on down is asking us to minimize our energy consumption, I took a look at my own electricity use. I didn't feel I was being wasteful, but I thought it would be interesting to just take a look and see. What I found surprised me - and helped me to save $300 per year at negligible cost.

My first step was to replace often-used lightbulbs with high-efficiency CFL-type bulbs. During the evening I often have my kitchen and living room lights on... in total, I use these lights maybe 2000 hours per year. I went down to the local home center and bought about a dozen discounted CFL bulbs of various wattages (from 13w to 27w). I replaced the bulbs in the kitchen, bathroom, living room, bedrooms, and office. In all, I figure I save about $150 per year in electricity alone, thanks to the CFL bulbs!

By the way, my new CFL bulbs aren't nearly as sucky as the old-fashioned ones I used five years ago. These new ones are at full brightness almost immediately after I switch them on, and and they seem to last forever (at least so far!). I did buy one lousy batch of CFLs - the lousy ones brighten slowly - but these few slow-start variants are the exception (and weren't much of a risk at only $0.99 each).

After addressing the lighting, I moved on to exploring how much electricity my appliances use. In order to easily and accurately measure my electricity consumption, I bought a simple watt meter called a kill-a-watt (about $30). I temporarily plugged appliances into this little meter in order to measure their consumption.

I found that my fridge consumes an average of 65 watts of electricity. My desktop computer system sucked down over 120 watts - with the monitor off! I also looked at a collection of appliances like clocks, the TV, the VCR, and so on.

My goal here was to simply minimize. There were some easy targets. Rarely used stuff was simply unplugged. But there were some really big money savers.

My fridge's "anti-sweat" option was turned on. This option is designed to keep the fridge from dripping water when it's extremely hot and humid. But do you know what? It's only like that a few days a year where I live. So for me this anti-sweat option does nothing but consume 16 watts for 8600 hours in a year. Keeping it on costs me $19+ per year and provides zero benefit. So turning the anti-sweat option off was a no-brainer.

Also, my fridge was running too cold. A thermometer showed that it was running at 32F (fridge) & 0F (freezer). I've seen suggestions that making your fridge too cool is of no benefit and can cost up to 20% of operational costs. So I adjusted my fridge to run at a recommended 40F, and 5F for the freezer, saving me perhaps another $25 per year.

The other thing I did was to turn off an infrequently used computer. Instead of a 120+ watt device running 8800 hours a year, now I run it for about 100 hours a year. That's a good $140 savings.


Seller Beware

I was bored a one day and decided to put up some ads on Craig's List - you know, I wanted to sell some of my junk.

So I put up an ad a got a reply from a guy named Bobby. Bobby is overseas, and he is looking to buy a junky $100 bike from the good old U.S.A. He also owns a shipping company.

It also happened that Bobby needed a $2,500 check cashed, and evidently he couldn't do it in his own country. Therefore, he asked me to accept a check for $2,500. Then I would then send him $2,400 and the bike. It'd be a win-win for everyone! His shipping company would pick up the bike later, so there'd be no shipping expense to me.

It's great that the internet can bring the world together, and allow people to rip-off others across the globe.

So I received the check via FedEx. The envelope was sent from Nigeria. But what do you know, the check turned out to be a fake - drawn on some poor soul's account. Good thing I didn't cash it and send Bobby the money - if I did, I'd be out $2,400.

Since then I've noticed a shocking number of people trying to scam me on my on-line ads. I recently tried to sell a crappy computer for $15 on Craig's. I got a weird reply from a potential buyer, and so I responded stating that my crappy computer was worth my $1500 asking price. Of course, the buyer was STILL interested, despite a two order of magnitude price increase. It's rare that I go to buy a $15 item, and remain agreeable when it turns out to be a $1500 item. The buyer, of course, was "located in the UK" and had a "special shipping arrangement with FedEx". Bah! On-line Ads: it's not only buyer beware - it's also seller beware. Or, just beware.

EasyN WiFi Camera Firmware Upgrade

I wanted to upgrade the firmware of my EasyN WiFi camera.  I just like to keep my firmware up to date.  I am sure it is a security sieve no...