Stop Giving Me Stuff I Don't Need

Whenever I buy a new phone, I always get a few bonus accessories in the box:

I don't need these accessories. I have many ear buds, many power chargers, and many cables. I don't need more.

PLEASE DO NOT INCLUDE THEM IN THE BOX.
PLEASE DO SOMETHING ELSE WITH THE MONEY.

When I get these, they just end up in a drawer, unopened. Within a few decades they will be thrown away. It is a total waste in every sense. I used to give these away, but nobody is really looking for them any more because almost everyone has a ton of them.

I realize that they might only cost a few bucks total to make, but multiplying it out means that many millions of dollars will be spent to make and throw away these items.

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair. Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator. Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way. Note in the pictures how I approach these tabs with my screwdriver. I usually release the left side first, and then I release ...

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full". A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual. He put the "light" Carbonator in the "empty" pile and sold me a different one. At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators. Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection. The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility. That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou...

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu...

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My Wahl 9918 Groomsman Beard and Mustache Trimmer has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more. Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl. Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws. By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a...

Why I get rid of stuff on Freecycle, eBay, and Craigslist.

Sometimes I have something that is old, worn out, or even broken, but I -know- that someone in the world could use it. For instance, the heating element of my coffee maker broke, but I knew that someone could use the coffee maker's carafe and filter basket. I listed those two parts individually on eBay, and they sold right away. I didn't get a lot of money for them, but I got enough to cover my costs. Why bother? Yes, I didn't make a ton of money selling my defunct coffee maker's carafe and filter basket. So what's my logic for selling them on eBay? It's better for my stuff to be used, instead of it being thrown into a garbage heap. It's better for my stuff to be used by someone who needs it, instead of having it sitting idle in my attic to rot. It's better for someone else to be able to fix their own thing with an inexpensive used part, instead of them having to throw away their old thing and buy something new. It's better to repair stu...

Fix a Lightning Cable with Heat Shrink Tubing

We've all seen a Lightning cable that has started to fall apart. They get used every day, and after enough tugs and yanks on your iPhone, they start to fray. I've seen a lot of these frayed cables, so I've started to fix them before they break with heat shrink tube. I get my heat shrink on Amazon, like this handy and inexpensive pack. I prefer the heat shrink tubes without internal glue - it has higher flexibility and a smaller outside diameter once shrunk. Heat Shrink Tubing on an Old, Frayed Lightning Cable In the photo here, you'll see that I slid on a 1.25 inch length of heat shrink over the lighting connector, and then shrunk it into place. I chose a diameter that just barely fits over the lightning connector. In all, it took about 60 seconds to perform this repair. Warning: the white plastic of the lightning cable has a pretty low melting point. It seems to start to melt at about 125°C (or about 250°F), which is the same temperatur...

The Lance J. Technoweb

Search This Blog