Skip to main content

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25?

My Wahl 9918 Groomsman Beard and Mustache Trimmer has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more.  Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money.

In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl.  Read on to find out how.

I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws.  By removing the two screws I was able to easily open up the unit, revealing the guts of the device.


Backplate off, Revealing the screws


The internals are rather simple: a motor, a simple circuit board, a switch, and a NiCad battery pack soldered into place.
The Internals, with new battery pack

I concluded that the battery was no longer holding a charge, so I worked to replace it.  I bought a set of NiCd Rechargeable AA Cells with Solder Tabs.  The solder tabs are very useful - they make it reasonably easy to solder together a new battery pack.   You can also buy pre-assembled packs to repair Wahl, Norelco and Remington products with, for example, the battery packs found here.

To create a new battery pack using two cells, I used some electrical tape to wrap together the two new cells, in plus-to-minus orientation.  Then I used a trusty soldering iron to solder one of the plus/minus tabs together.  I pulled the foam off the old battery pack and stuck it onto my homemade pack.

Then I unsoldered the old battery pack from the Wahl and soldered my new pack in its place, ensuring that I kept proper polarity.

After, I cleaned up some corrosion on the switch with a pencil eraser and an emery board, and reassembled.  A little test proved good, and so I plugged in the trimmer and let it charge overnight.

Now the Wahl works like new! It runs perfectly and charges perfectly to.  It continues to provide me with a beautiful beard, 15+ years running.

UPDATE, 2019-07-06

In my haste to trim my beard, I dropped my beloved Groomsman onto the bathroom floor resulting in the cutting head detaching from the body.  The plastic mounting posts of my Groomsman had cracked, leading to loose screws.  The cutting head would not say attached to the body.  Ug!

I was planning to resign and buy a new Groomsman, like this one.  After all, the cracked part of my Groomsman is normally under a significant amount of stress, squeezing down on the spring system of the cutting head.  It seemed like a plastic structural repair would not be reliable.

But I love the Groomsman that I've owned for so many years.  I decided that it would be worth trying to repair the cracked plastic posts with that super standby, cyanoacrylate adhesive (super glue).

I cleaned the broken plastic with rubbing alcohol and let it dry.  Then I used small dots of liquid super glue (not the gel kind) on the broken plastic parts and held it all tightly together with some tape and rubber bands.  I let the adhesive cure for a full 48 hours in a humid environment (that's how super glue cures!  Humidity!). Then I carefully reassembled my Groomsman by mounting the head back on the body with the two mounting screws.

The result? Excellent! My Groomsman lives on, for a mere 10¢ worth of epoxy.

 Don't give up!  Keep your Groomsman grooming.

 

Labels:

Popular posts from this blog

The Trick to Properly Fixing the Rubber Feet of a MacBook Pro

A black rubber foot of my trusty old MacBook Pro finally broke off, and I didn't like how it made the laptop wobbly.  A fix was needed, and quick! First I bought some replacement feet, the kind that just stick on.   These feet are nice because there is no need open up the machine to fix a broken foot.  They're very inexpensive, and the ones I bought have adhesive tape already applied - just peal and stick.  I bought feet like the ones found here. I have read many complaints about how the adhesive doesn't stick, but I think that's because people don't know the two tricks required to get the new feet to stick properly. New Feet to replace a lost Foot Important Trick 1: Make sure to remove all remnants of the old foot - including the pieces in the hole.   My factory-installed foot was attached both mechanically and with adhesive, but when the old foot sheared off, some pieces of the old foot remained in the hole.  Those plastic bits would h...
Read more

Canon SD890 Review

My Canon PowerShot SD890IS Review Wahoo! I just received my new Canon PowerShot SD890IS . Here's my review of the new SD890IS. Updated! (20-April-2008)! I like taking good photos. And I hate lugging around big cameras and equipment. And so I concluded that I needed to buy myself an awesome point-n-shoot camera. I often take pictures in difficult conditions, such as a museum where a flash camera is prohibited. Or a concert, where I can't use a flash, the lighting is low, and the people on stage are in motion. Or with the zoom cranked up and focused on a distant subject. Taking good photos in these conditions, with a small lens camera and without a tripod is a challenge at best. In comes the SD890. I was particularly excited about the SD890 because it is pocketable, yet it has awesome specifications: Image stabilization ; a 5x zoom lens, and 10 megapixel resolution. When I bought the camera, I imagined that these features would help me take much better pictures in the...
Read more

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full".  A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual.  He put the "light" Carbonator in the "empty" pile and sold me a different one.  At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators.  Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection.       The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility.  That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou...
Read more

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu...
Read more

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair.  Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator.  Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way.  Note in the pictures how I approach these tabs with my screwdriver.  I usually release the left side first, and then I release ...
Read more

Using a Directional WiFi Access Point - the TP-Link CP210

I have two buildings on my property, and I wanted to bring Internet to my garage without pulling a wire. Previously I was using the barely-adequate reach of my house's WiFi, but it was just a little too far and it would drop frequently enough to be painful. My solution is a WiFi Directional access point - the TP-Link CP210. I chose the CP-210 because it was inexpensive. It only supports the 2.4 GHz band, but my goal was quality over performance. In all, it does this job perfectly. I mounted the CP-210 in my attic because it was easier to install that way. If I really wanted to I could mount it on the outside, but that means drilling holes and climbing a ladder and other things that I don't want to do. After all, it works great from inside - an outside mount isn't going to give me anything more except more work. I simply pointed the CP-210's antenna to my garage and that was it. Easy and effective. The CP-210 has a bunch of useful configuration options - it isn't jus...
Read more

Other Posts

Show more