Skip to main content

Belkin F5D7230-4 v2000 and DD-WRT

I recently upgraded my Belkin F5D7230-4 v2000 802.11g router with DD-WRT.

For those not familiar with DD-WRT: It's alternative software for a large number of routers. This replacement firmware provides a boatload of features and capabilities that let you maximize your router's potential. After all, the core of a router is a computer.


I didn't have much luck with it with the original Belkin-provided firmware. But with DD-WRT it has been fantastic: fast and stable, with a good range of features.

I was surprised that router is supported by DD-WRT - the v2000 has a limited amount of memory, but sure enough it was on the official support list. With only 2 MB of on-board flash storage, it can't do everything. But with DD-WRT it can do way more than many new, expensive routers.

Limitations of the V2000 with DD-WRT

You should know that there is a limitation with this particular router and DD-WRT. For technical reasons, the old "Cable Modem" port doesn't work. This implies a loss of functionality. But there is a work-around if you can do without wired clients like I can.

And, of course, messing with firmware isn't easy and can damage your router. So proceed with caution!

Steps

This is what I did to install and configure DD-WRT on this router:
  1. I downloaded the DD-WRT firmware. I chose the biggest "Bv2000 Micro-Plus_SSH SF" version, as downloadable from here: dd-wrt.v24-13491_Bv2000_micro-plus_ssh.bin
  2. Next I installed the firmware file using tftp, as described here: DD-WRT install
Enabling the Ethernet ports

At first DD-WRT thinks that your router is a v1444, which has slightly different ethernet hardware. But it isn't - it's a v2000. So to enable the ethernet ports, DD-WRT needs to know that you actually have a v2000.
  1. From my computer, I wirelessly connected to the dd-wrt router SSID
  2. With my browser, I went to http://192.168.0.1/ and set the username to "root" and the password to a good password.
  3. From a terminal command line, telnet to 192.168.0.1
  4. login with the username/password you set above
  5. Run the following commands:
nvram set Belkin_ver=2000
nvram commit
reboot
After the reboot, the LAN ports will be enabled. You should be able to connect an ethernet cable to the router and get a DHCP address and administrate the device.

Enable the ports as WAN

Sadly, the "cable modem" ethernet port of the v2000 remains disabled due to that pesky DD-WRT limitation. What to do? Use the quad ethernet ports for WAN:
  1. Go into the web administration interface.
  2. Choose the "Setup" tab.
  3. Choose the "Network" tab.
  4. Set WAN port assignment to "eth0".
Now ethernet ports 1-4 are associated with the "WAN" side of the router. The original singleton "cable modem" port is useless. The WIFI is associated with the LAN side of the router.

These ports 1-4 operate as switched ports on the
WAN side. Don't use the "cable modem" port.

Now, plugging the cable modem into any of the ports 1..4 results in the router obtaining an address! Yay! It works!

Finally, after getting all this stuff working, I finished configuring the device:
  • Set up wireless security on the router
  • Configure SSH, DDNS, remote admin, etc.
Conclusion
I have to say that my Belkin is much more reliable now - in fact, I have yet to reboot it. Pretty awesome. I do miss having LAN ports available to me - hopefully someone with deeper knowledge of the device will provide the software necessary to control the ports in the way the device's creators intended!
Labels:

Popular posts from this blog

Fixing a SodaStream Jet, part 1: Disassembly Guide

I've had my SodaStream Jet for years, and once in a while something has gone wrong. Disassembly is the first step to repair.  Start with this article to see how to disassemble the SodaStream, and then once you have that down, scroll through my other articles to see how I repaired specfic SodaStream problems. SodaStream Jet Disassembly Guide Tools Required Flat head screwdriver Phillips head screwdriver 1. Remove the Carbonator.  Duh. 2. Remove the black panel lever The front big black tilt lever needs to be removed first. Removing this panel is tricky, but it isn't impossible. Looking up at the bottom of the black panel, there are two tabs, one on the left and one on the right. These tabs fully secure the panel in place. The trick is to use a flat-head screwdriver under the plastic to gently lever the tabs out of the way.  Note in the pictures how I approach these tabs with my screwdriver.  I usually release the left side first, and then I release the right
Read more

Fixing my Wahl 9918 Groomsman Beard and Mustache Trimmer

Not everyone would bother repairing a $25 beard trimmer, but why not fix something for under $5 instead of spending another $25? My  Wahl 9918 Groomsman Beard and Mustache Trimmer  has admirably performed its beauty duty for many years, but the time came when the battery just wasn't holding a charge any more.  Most people would just put the trimmer in the trash and buy a new one, but I figured I could repair my otherwise excellent Wahl and save some money. In fact, even high priced trimmer and rotary shaver brands, like Norelco and Remington, can be easily repaired using a process similar to the one I used to fix my Wahl.  Read on to find out how. I opened up the Wahl by popping off the black plastic faceplate with a tiny flathead screwdriver, which revealed two screws.  By removing the two screws I was able to easily open up the unit, revealing the guts of the device. Backplate off, Revealing the screws The internals are rather simple: a motor, a simple circuit boar
Read more

Sodastream Carbonator Leakage, Usage, and Weight

SodaStream 60L "Carbonator" CO2 cylinders have a specific weight when empty, plus about 410 or so grams for the CO2 they should have when they're "full".  A little while ago I went to buy a replacement Carbonator from my local hardware store. The dealer pulled a new Carbonator out of the box and sensed it was lighter than usual.  He put the "light" Carbonator in the "empty" pile and sold me a different one.  At that moment I concluded that it would be smart of me to weigh both new and empty SodaStream carbonators.  Here are the results. Weighing a SodaStream Carbonator - for both Science and Consumer Protection.       The dealer told me that sometimes the carbonators leak after they leave the SodaStream filling facility.  That means there could be an opportunity for customers like me to get ripped off! The SodaStream cylinders I buy claim to have a net product weight of 410 grams - and that means that a full Soda Stream Carbonator shou
Read more

Fixing a SodaStream Jet, Repair #2 - Broken Fill Button

My Soda Stream Jet's fill button broke, which means I can not longer carbonate water by pressing the pushbutton. This caused all sorts of grief in my household. Here is how I managed to repair my Jet to give it another 10 years of life (hopefully). First, a look at the button The fill button on the top of the SodaStream is actually a simple lever. Pressing down on the button moves a pin that does the actual work of pressing open the Carbonator's valve. Unfortunately, the axis point is fairly thin and can see a lot of stress. That's where my Soda Stream button cracked. [ I think the usage tip here is "don't over-press the button like a gorilla, it doesn't do anything but put high stress on the button."] Cracked levering point of the button The Pesky Lever Retaining Pin The Fix It was pretty easy for me to replace the button: Take off the back of the Soda Stream and remove the carbonator. Push out the the button lever's steel retaining pin. This takes qu
Read more

The Yamaha DD-65 and YDD-60 Digital Drums

Almost everyone I know who is into drums should get their hands on the Yamaha DD65 . It's a low cost, fun little kit that you can throw in your car to jam with your buddies. It's a lot easier than throwing your gear in your Subaru. The DD-65, also known as the YDD-60. Eight pads in a pretty package. I've owned the older, venerable DD-55 for about five years. The DD-55 is the ancestor of the newer DD-65, and is an evolution of the DD-50, which was first released some time in the mid 1990s. I just put my DD-55 on this light snare drum stand it's ready for some jamming. The classic DD-55. Seven pads of rockin' fun, since about 2001. Yes, everyone will tell you that the DD-55 isn't actually a real drum kit. No kidding. However, a skilled drummer can get some great sound out of this little box, and you can definitely keep the band together with it. Plus, it's perfect for apartment living.
Read more

Adding a Water Flood Sensor to my Vista-20p alarm system

My Honeywell Vista 20p alarm system is fairly comprehensive, but I want one more feature: an alarm that lets me know when my sump pump isn't working properly. Here is how I added one for about $8 in special parts.   I'm afraid of a flood in my finished basement. I'm fortunate - my basement sump pump system is already redundant, with two independent pumps and two outflow pipes. The primary pump kicks in when the water level reaches 6 inches, and if that doesn't work, then the backup pump kicks in when the water level reaches 7 inches.  The backup pump should never kick in unless the primary pump is having a problem pumping.   But there is a problem with this setup: I might never know if my primary pump has failed, leaving me with no redundancy.  I want to be informed when I have one (or god forbid, two) pump failures. My goal is to have my Vista 20p alert me when the sump's water level is ever beyond the point where my primary pump should have kicked in, alerting me
Read more

Other Posts

Show more